YOUR COMPLETE TUTORIAL FOR INSTALLING A BATHTUB

Your Complete Tutorial for Installing a Bathtub

Your Complete Tutorial for Installing a Bathtub

Blog Article

Give Me A Quote!

They are making several great pointers on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround in general in this article on the next paragraphs.


Installing A Bathtub
Installing a bathtub isn't precisely rocket science, yet it does call for strong plumbing, carpentry, and sometimes, tiling skills. Changing an old bath tub with a brand-new one is also a moderately challenging project. If the old bathtub is easily obtainable, the job can move easily; if you have to open up a wall to get rid of the old tub and place the new tub, the job is much harder. In either situation, the task is within a house handyman's abilities, although you will certainly require a helper to leave the old bathtub and set in the new one. See to it you have certified yourself for the task and also fit trying it. As opposed to hiring a professional to take over a halfway-completed project, it is better to think about utilizing one before you begin. Opportunities are you might require an expert plumber to make tube connections.
This post will certainly aid you set up a brand-new bathtub in your restroom if you have actually currently purchased a new tub and do not need to alter the plan of your previous supply of water pipes.
Your devices and also material list ought to comprise the following:
  • New Bath tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipeline Caps


  • Preparing for the Installment


    To start with, the supporting framework provided with the bathroom needs to be fitted (if required) according to the producer's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is important to make certain that if the faucet features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the taps unit to prevent strain on the bath tub.
    Fit the adaptable tap adapters to the bottom of the two taps utilizing 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the supplied washers.
    Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath need to now be ready to be suited its final setting.

    Removing Old Touches


    If you require to replace old faucets with brand-new ones as a part of your installation, then the first thing you should do is disconnect the water system. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be rather troublesome as a result of the limited gain access to that is commonly the situation.
    Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the taps. Have a cloth all set for the staying water that will originate from the pipelines. When the supply pipes have been eliminated, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the solitary faucets from turning during this procedure. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any old sealing compound.
    Before going on to fit the brand-new taps, contrast the pipeline links on the old taps to the brand-new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the new taps to fit.

    Mounting the Bath tub


    Using the two wood boards under its feet, position the bath tub in the called for setting. The wooden boards are helpful in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 small factors.
    The next goal is to make sure that the bathtub is leveled all round. This can be accomplished by examining the level and changing the feet on the tub up until the level reads degree.
    To install faucets, fit all-time low of the outermost adaptable faucet adapter to the ideal supply pipeline by making a compression sign up with; then do the exact same for the other faucet.
    Turn on the water system as well as check all joints and also new pipework for leaks and also tighten them if needed. Fill the bath tub and additionally check the overflow outlet and the typical outlet for leakages.
    Lastly, take care of the bathroom paneling as defined in the supplier's instruction manual. Tiling and securing around the bath tub needs to wait until the bathtub has actually been made use of at the very least when as this will settle it into its final position.

    Suitable New Taps


    If the tails of the new faucets are plastic, after that you will need a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipes.
    If you require to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
    Next off, place the faucet in the placing hole in the bath/basin making sure that the washing machines are in place between the faucet and also the sink. Protect the tap in position with the producer provided backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical faucet ports. The previous kind ought to be attached to the tap ends initially, tightening up only by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.

    Tiling Around the Bath tub


    In the location where the bathroom satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to fracture a stiff seal, causing the water to pass through the wall between the bath as well as the tiling, resulting in complications with moisture as well as possible leakages to the ceiling below.
    You can select from a selection of coloured sealers to blend in your components and fittings. They are marketed in tubes as well as cartridges, as well as can securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water prior to sealing, to allow for the activity experienced when the tub remains in usage. The sealant can fracture fairly early if you do not take into account this motion prior to sealing.
    Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally easily available on the market. It is suggested to fit the ceramic tiles using waterproof or water-proof adhesive and also grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    A Step-by-Step Guide to Installing a Bathtub

    I came across that blog post about A Step-by-Step Guide to Installing a Bathtub while doing research the web. If you enjoyed reading our article kindly remember to pass it around. I recognize the value of reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.


    Immediate relief, just a call.

    Report this page